Home Blog Page 142

POLARIS 4-STROKE LOGIC

0

We’ve guessed, postulated and waited and so far we haven’t seen a hint that Polaris has any desire to begin offering a 4-stroke snowmobile any time soon. This doesn’t mean something isn’t brewing, however.

So far, Polaris has limited its market to only offering 2-stroke powered snowmobiles and has had pretty impressive success with that strategy.

The company continues to hold second-place market share in the industry and its SDI 2-stroke technology is fuel efficient and very powerful.

Here’s the rub: It’s questionable whether or not Polaris can grow its market share without dipping a toe into the 4-stroke market. Some authorities tell us that 4-stroke shoppers only comprise about 20-percent of the industry’s total sales.

This seems arguable as we continue to see more and more new-sled buyers at least giving serious consideration to 4-stroke sleds before buying.

Also, the Yamaha and Arctic Cat turbo-sleds have swayed a considerable number of high performance buyers over to the 4-stroke world.

Here’s the elephant in the room: Can Polaris sit out the 4-stroke market much longer?

We think the company has been building chassis prototypes and 4-stroke snowmobile engines for several years. So far there’s been no commitment to a final design but the engineering teams have the capability to pull the trigger on a new 4-stroke when the time is right – and do it on fairly short notice.

We’ve predicted an engine based on the very strong turbocharged DOHC twin used in Polaris’ off-road RZR 1000. This engine already delivers power in the 160-hp range and is CVT-friendly.

A twin would fit the AXYS front clip better than a triple – although considerable alteration of the engine bay would be required – especially if the engine were to be turbocharged.

Another twist would be an all-new engine using the RXR 1000’s head design but a 3-cylinder configuration instead of a twin.

We’re thinking MY 2019 might bring the answer we’ve been waiting for.

IMPACT OF SNOWMOBILING

0

Someone once said: “If you really want to be proud of your country, get out and take a look at it!” Snowmobilers do that every time we go for a ride – and although the experience of riding a powerful vehicle is exhilarating, so is the experience of being completely immersed in a pristine winter environment.

Sometimes I think about riding my sled out of a shaded forest glade on a zero-degree January day into an open meadow where the winter sunlight beams down, then running along the backside of a village where just a few hundred feet away, people are bustling about, going through their daily lives, oblivious to the beauty and freedom that lies within shouting distance.

Some environmentalists will try to tell you snowmobiles aren’t good for the eco-culture. These are the same ones who use major airlines at will to hop-skip across the continent so they can share their green message to the world.

They might need to learn that a single day spent on a snowmobile trail network reveals more appreciation for the environment than any number of lectures on a university campus.

Do snowmobiles compromise the flora and fauna and the air we breathe? As a total influence worldwide and given that so much progress has been made in clean technology the last decade, I’m shouting a profound “NO”!

Are we contributing to global warming and climate change? Certainly no more than a couple of thousandth percent points of what air traffic and industry pollutes in a single day.

I’m not meaning to condemn airlines or flying – we need to use these services ourselves sometimes. Rather it’s a criticism of the ‘experts’ who will try to sell the lie that snowmobiling is some kind of major contributor to environmental doom because it’s a fun and performance-driven motorized activity – a very soft target.

Frankly, although snowmobilers don’t tend to stand on soapboxes and orate about how they respect the environment, we’re out there amidst it, experiencing the beauty and fragility of a winter world 98-percent of the population are completely unaware of.

I haven’t met too many snowmobilers who profess to being eco-greenies, but I’ve met dozens of snowmobile club volunteers who go to painful lengths to ensure no damage or footprint is left when building or grooming a trail.

These same saints are the ones who pick up the garbage left behind by a few lazy and inconsiderate participants who unfortunately are found in every activity mankind is involved in.

There’s a big difference between preaching and doing. Every time you ride, be thinking about how you can enjoy it and then go home without leaving a mark.

Better yet, lift up your eyes every now and then from the 100 square feet of trail in front of you and take in the panorama surrounding you – and know this: You’re one of the very few who gets to see it!

THE NEXT VIPER

0

The introduction of the turbocharged SideWinder last year has provided a number of clues about what could happen with a second generation Viper.

Here are some things we think could be coming:

Utilization of the SideWinder’s YSRC roller secondary

This is the very least Yamaha could do with the 1049cc Yamaha triple and our guess is the company was doing field-testing with it all last winter.

New bodywork

Everything is there and already being used on the SideWinder. Yamaha has spent a ton of money designing and building molds for the SideWinder’s quick-remove body panels – makes sense a new Viper would use them, too – or at least a variation of them.

Electronic Throttle Control

YCCT (Yamaha Chip Controlled Throttle) is a flawless system and so far has only been used on the RS-based Vector and Venture. It’s well proven technology and a next-gen Viper would have a lot of sizzle with it onboard.

SingleShot Skidframe

Some have told us we’re nuts to even think about this but it makes sense from a weight-saving perspective. The 129 and 146-inch Vectors and Apexes with this skid work very well and it’s lighter. It would also make the Viper more distinctive from the Arctic Cat 7000 versions.

Power Steering

Certain upgrades of the Viper and the new Venture SR could adopt EPS. This long-tested tech is well proven and makes a deluxe version of anything Yamaha pretty appealing.

EX-UP

Here’s a stretch: Suppose the Apex’s unique EX-UP exhaust valve was adapted to the 1049 triple? Yes, there would be special challenges placing it in the tunnel of the SR platform. However, we think it could be done and may amp up the Viper’s power and torque without a lot of EPA hassling.

IEM & MFG. CELEBRATES 50 YEARS

Hope, MI: International Engineering & Manufacturing, Inc. (IEM), established in 1968, celebrates fifty years of success as the leading manufacturer of snowmobile traction products trademarked as Woody’s. The company will commemorate this occasion with their friends and fans throughout the 2017-18 show season, as well as with affiliates in the Spring of 2018 for a formal gathering. Their festivities will kickoff this year at Hay Days in North Branch, MN the weekend after Labor Day. Additional excitement includes Woody’s Facebook event called 50 Weeks 50 Giveaways, in which followers are given 50 chances to win prizes throughout the season.

Company President, Robert Musselman, states, “All of us here at IEM/Woody’s are extremely proud of this milestone. We would like to personally thank our enthusiastic supporters who helped make this achievement possible, including our customers, suppliers, distributors, manufacturers, employees, and the snowmobiling community. As we reflect on IEM’s first fifty years of successes and experiences, we also want to take this time to embrace our vision looking forward. We are excited for future opportunities in our industry and will remain committed to growth, diversification, and excellence in customer service and product quality.”

The story of a successful company began in the mid-sixties as James Musselman and Woody Kozlow put their minds together to revolutionize snowmobile racing by developing the first ever carbide runner. Instead of using three corner files attached to ski bottoms for handling and traction, they decided to use their knowledge of carbide wear characteristics and attach the carbide to a metal base. This was an instant breakthrough in the industry, and soon everyone wanted a pair of “Woody’s” carbides. Shortly after, carbide tip studs were developed and the pair became essential for racing, eventually making Woody’s synonymous with quality in snowmobile traction products.

Today, IEM is a small town, family-owned company managed by second generation Musselman family: Robert Musselman, President and Mark Musselman, Vice President. They currently employ 53 full-time employees, who are all considered family. Perseverance, hard work, innovation, and unwavering commitment to quality products and customer service is what transformed IEM into the international corporation it is today. To change with the times, an office renovation along with a new and improved website can be expected in the near future.

POSSIBILITY OF A CONSUMER G4 600

0

We’ve been stoking rumors of an all-new 600 from Ski-Doo ever since we laid orbs on the 850.

It just makes sense Ski-Doo would utilize its very advanced G4 platform for more of its models and, if this year is any indication, the company has already swapped out sleds like the Renegade Backcountry, the Freeride and others into the new chassis.

We think Ski-Doo and Rotax have been holding off a couple of years on the development and certification of yet another new E-TEC for the G4 – and that would be a 600-class powerplant.

With the recent debut of Ski-Doo’s 600cc snocrosser, the MXZ X 600 RS, there are some clues about what a new 600 would look like.

The RS, essentially a racing-only sled and engine, has a number of new tricks not used before in the old XS-based RS. First, the RS’s 600 (599.4cc) uses 850-inspired booster injectors, double reed valves and a shorter intake length (this gives the engine incredible throttle response and “snap” when you tip-in the throttle).

Also, this new 600 is a mono-block – much lighter – and has redesigned RAVE exhaust valves very similar to the 850.

We haven’t heard whether the 600 uses the flat stator and narrower width of the 850, but if it didn’t, it would be considerably harder to shoehorn it into the narrow G4 bulkhead.

We’re presuming this mono block is an-all-new casting along the lines of the 850 and will certainly accommodate the narrowness of the chassis.

All these changes are a pretty big investment and give clues to the fact there’s a new consumer 600 coming.

One question: Will it be a 600 or a 650? Although we made guesses about the 850, we never expected Ski-Doo to punch out the 800 to bigger displacement.

It changed all the rules and the company might be doing it again in the 600 class.

DEFINING FAST

0

We get lots of comments on articles we post about “fastest sleds”. Interest has amped way up the last two years with the introduction of new powerhouses like Yamaha’s SideWinder turbo , Cat’s Z9000 turbo and Ski-Doo’s 850 E-TEC.

To top all that, Cat is finally offering its long-awaited 800 DSI 2-stroke for MY 2018. These engines are among the fastest ever offered in the snowmobile business and, along with Polaris’ 800 HO, put tremendous focus on sleds that are categorized as “fast”.

The question is: What is “fast”?

Fully clutched out and pulling all the engine’s top end on a hard-packed surface resulting in a very high top speed is usually the definition of “fast”.

This may not necessarily be accurate because it could be the result of the engine being geared higher and the engine’s torque curve allowing the clutches’ calibration to go to maximum shift and pull really high speeds at top end.

The alternate definition is the rate of acceleration a sled can achieve in a set distance – sort of like a drag race. The shorter the “drag strip”, the “faster” the sled will seem when it beats other sleds with more horsepower in a short or pre-determined distance.

There are other factors that come into play, too. Clutching is one of the biggest: If an engine can get its drive system up to top speed by squeezing the primary harder and reaching optimum clutch shift-out, it can overcome other sleds with less efficient clutching but more power. Hardcore drag racers have known this for decades.

Traction is a big factor, too. Even at top speed at the end of the lake, these big, new engines are slipping the track a surprising amount unless you’ve installed some aggressive traction products.

It goes without saying that when accelerating in the drag race scenario, traction is a huge factor and if your rate of acceleration is lost to track slippage, it doesn’t matter how much horsepower or torque your sled is making.

So what’s fast this year? Without question, the two turbos are the fastest in both drag race and top speed situations. The huge torque numbers generated because of the Cat and Yamaha’s turbochargers allow for maximum clutch shift-out faster.

Frankly, even if these engines were producing less horsepower than their claimed 180-ponies, they’d still be faster than the 2-strokes by virtue of their gargantuan torque outputs and ability to squeeze the belt and still pull tall gearing.

Of the 2-strokes, we’ve found the Ski-Doo is fastest by virtue of its pDrive clutch efficiency and extra 50cc’s of displacement – once again, amping up the engine’s torque numbers so it can pull more top end with taller gearing.

Not far behind the 850 are the DSI 800 Cat and the Polaris 800HO. So close is the performance of the three 4-strokes that on any given day one can beat the other depending on weather, traction conditions and clutch tuning.

Let the arguments continue.

REACH FOR THE SUMMIT SHARED EXPERIENCES

0

Congratulations to Michael Helfrick for sharing his REACH FOR THE SUMMIT experiences. Michael picks up the Cyclops GEAR CGX2 4K Wi-Fi Action Camera! A great camera for capturing your experiences!

Michael’s submission is a great example of one of the reasons we chose Sicamous BC for our grand prize because these are the types of experiences you can expect.

Michael writes:

“I’ve been snowmobiling since I was 12 and have never found better riding than Sicamous BC. There’s endless untracked powder in the trees if you know where to go and miles and miles of groomed trails if you don’t. I’d love a chance to get to ride there again and hang out with some of the big dogs at CKMP.”

Supertrax Media Inc. in cooperation with Ski-Doo snowmobiles is promoting the Reach For The Summit Sweepstakes. Enter and you can WIN an all expenses paid mountain riding adventure at CKMP (Carl Kuster Mountain Park) in beautiful British Columbia, Canada.

While there you’ll not only enjoy 5 star accommodations, you’ll also get to hang out and ride with Ski-Doo Mountain Ambassadors Carl Kuster, Rob Alford and Tony Jenkins. The lucky winner will also star alongside Luke and AJ Lester in a feature story on SnowTrax Television and be the focus of an article in Supertrax Magazine!

Enter now at supertraxmag.com/summit

DECODING YAMAHA’S NOMENCLATURE

0

Some of you have asked us what the various alpha-numeric names associated with Yamaha snowmobiles mean and how you can determine what models have what features.

Here’s our best stab at interpreting the jargon:

TX: As near as we can figure, “TX” means “Yamaha snowmobile”. It is used in every segment, accompanied with other letters, to signify model categories.

R-TX: The “R” stands for “race” … kinda. What it really signifies is the sled’s track length and the fact it is most likely to be used for aggressive, quick-turning trail riding. All “R” models feature a 129-inch track and a coupled suspension.

L-TX: The “L” designation means “long track” and the L-TX is a trail-targeted sled with a 137-inch track and a coupled suspension. Basically, it’s an R-TX with a longer track.

X-TX: The “X” stands for “X-Over” or crossover. These Yamahas are intended to be dual purpose sleds that can be driven on trails competently and also work very well in flatland powder and the foothills. Most use a 141-incher (all SR) but some have a 144 (Phazer) or even a 146 (Apex). All X-Series use an uncoupled suspension.

B-TX: The “B” stands for back country. These Yamahas are close to being mountain sleds and are very serious for freeriding in powder snow. They feature more aggressive tracks than the X-TX series and have some fairly sophisticated shock packages. Suspensions are good but their deeper lugged tracks (1.75 & 2.25) tend to limit their trail use.

S-TX: When we interpret the “S” in S-TX, We’re thinking it means “standard”. These more basic track and shock equipped Yamahas are usually accompanied by the term “DX” which usually stands for “DeLuxe”. However, this probably refers to the type of ride and comfort you get (higher, warmer windshield and more ride compliance) and not a deluxe performance shock package.

M-TX: The “M” is for mountain. Nuff said.

LE and SE: There are significant differences between models designated with the LE and SE nomenclature. The LE stands for “Limited Edition” and is usually a limited availability, order early model with special track and shock features. We think SE stands for “Standard Edition” which is the baseline, in-season snowmobile offered in that particular segment.

SR & RS: These signify the type of chassis the snowmobile is built on. The RS is the original rider-forward, built-in-Japan chassis used on the Venture, Vector and Apex. SR signifies Yamahas built on the Arctic Cat chassis like the SideWinder, Viper and new SR Venture DX 2-upper.
VK: VK is short for “Viking” – nearly all utility models carry the VK designation.

BAT: This means “Best Available Technology” and is used on the RS Venture TF for use in public park areas where snowmobiles would ordinarily be banned. These sleds, usually rentals, have the ultimate approval and equipment to certify with the EPA for squeaky-clean emissions.

TF: This is basically, a regular 144-inch RS Venture with a longer 151-inch track. We’d like to think it stands for “Two–FER”.

MP: This term, meaning “Multi-Purpose” is used on the 500cc Venture MP which doubles as a touring sled and a utility sled.

There you go. If there are any we’ve missed, let us know and we’ll guess along with you.

2018 CKX TITAN HELMET

0

Last year, CKX launched the Titan, a unique helmet that combines the features of a backcountry and modular helmet.

For the first time, a helmet benefited from the look and weight of the MX helmets, while enjoying the comfort of a modular helmet.

This year, wishing to improve, the CKX team relied on users’ feedback, research, analyses and tests with numerous snowmobilers to develop the new versions of the CKX TITAN.

While maintaining its signature backcountry look with a retractable and detachable muzzle, as well as the built-in wide-angle (210o) goggle, CKX took on various technical aspects to improve the snowmobiler’s experience in different conditions. We all know that snowmobiling is not the same for everyone.

But what makes the CKX TITAN unique?

– First, there is the muzzle allowing the user to free his face easily.​

– Also the unrivaled goggle with a 210° field of vision. A goggle designed along with the helmet for a perfect fit.

– And it’s a helmet that provides the user a unique quick-attach system (patent pending), allowing the goggles to be placed on top of the helmet to protect them from the elements.

2018 POLARIS TITAN SP

0

You may be thinking the industry has gone nuts when you read about sleds like the new Polaris Titan SP.

At first glance it looks like a performance sled. However, it seems like the Titan SP breaks every rule of performance snowmobiling: It’s huge – but it’s got a big, powerful 800cc 2-stroke.

Its massive track is 20-inches wide and 155-inches long. Yeah, plenty of surface area – but what about all that power-robbing weight?

It’s supposed to be a utility-style sled because it’s got wide workhorse skis and an articulated rear suspension, but it’s got mountain style PowderTrac running boards and all the hot rod electronic features of a top performing trail or mountain sled. What’s up?

We don’t know either, but this sled is a blast to ride. We suspect it’s designed to compete head-on with Ski-Doo’s Expedition Extreme – also a utility-adaptable sled with pared down looks and an 800 2-stroke under its hood.

Comparisons aside, the market for these sleds is to regional North American riders who boondock a lot and, especially, to Northern Europeans who ride Scandinavian terrain where there may or may not be groomed trails.

We rode the Titan last winter and were shocked at its maneuverability and light ergonomic feedback when you’re in the drivers seat. It handles and steers like an Assault and its suspension is as good or better than any trail-targeted Polaris.

Although the seat is wider because of its wide tunnel and track, it never feels cumbersome or particularly bulky. Five minutes in the cockpit and you feel right at home, honing twisty trails and launching into powder. The sled is surprisingly responsive to its driver’s body-english and responds off-trail like a good mountain sled.

We think some of this ergonomic bliss may be because the weight of the sled is pretty well-balanced. A front-weighted 4-stroke actually feels more intimidating in powder than the Titan but because the 800 is light and the weight of the engine and drive system is parallel throughout the chassis front to rear, it handles deep snow challenges really well. Fast? Plenty.

We’re curious to see how the Titan SP sells in North America. We know for sure there are riders in Maine, Northern Ontario, Quebec, Newfoundland and Labrador that have been waiting for a sled like the Titan.