Home Blog Page 396

North American Watercross Competition

Press Release –

This year,the CMEQ is presenting the 19th edition of its North American Watercross on August 25th and 26th, 2007 in Victoriaville, Quebec.

More than 60 racers from the United States and Canada will compete in drag, oval and extreme jump competitions.

The CMEQ will also be presenting special attractions for families such as water skiing behind a snowmobile, helicopter rides and much more….

For more information visit CMEQracing.com

2008 Ski-Doo Rev XP Track Length

Question:

For the 2008 Rev, I understand it is fitted with a 120″ track. Is there enough adjustment in the rear skid to fit a 121″ track if the pitch were compatible?

Thanks

Mike

Question:

Why change it to a 121? The new track is super light and strong – all you’ll do is increase weight – and you’re paying for less weight when you buy an XP.

It will be difficult at best to use any other track as the drive axle and the track pitch are unique. In other words you can’t change the sprockets with this axle to match an old pitch track.

You should note that only Woody’s has studs right now which will work with this track.

Thanks,

Motorhead Mark

Yamaha Technician Grand Prix

Press Release –

On June 19th, the Canadian finals of the Yamaha Technician Grand Prix contest will be held at the Toronto head office of Yamaha Motor Canada Ltd.

After advancing from the eight regional contests carried out from February to April, the top ten scoring competitors will compete for the National title and the honour of representing Canada at the Yamaha World Finals.

The World Finals will take place at Yamaha Motor Corporation head office in Iwata, Japan. Technicians at the Canadian challenge will be evaluated from three major activities:

• Written examination: Criteria includes but not limited to: Technical questions relating to Yamaha products, Innovative developments Yamaha has introduced as a leading manufacturer in the global motorsports industry.
• Practical skills contest: diagnostic and systems analysis and repair on the latest 2007 motorcycle product.
• Customer reception interviews: technicians are tested on their ability to provide a pleasant, yet thorough and satisfactory customer interaction through a reality-based interview.

Customer satisfaction is a primary objective of Yamaha Motor Canada, as such scoring well in the customer reception interview portion will be crucial to the success of the competitor.

Technical training and superior education is a major part of Yamaha Motor Canada’s continued direction as we continue to lead the industry with product developments and dealership assistance.

Yamaha has developed the Tech GP program in order to raise awareness and increase competency of those technicians that work under the Yamaha brand and foster the development of world-class technicians.

For more information about the Yamaha Tech GP, please contact:
Andy Gale Manager,
Service Marketing Yamaha Motor Canada
(416) 498 1911 ext 2507
andy_gale@yamaha-motor.ca

Xenoy* Resins Offer Solution to Vapor Permeation

Press Release –

GE Plastics today announced new grades of its tough Xenoy* resin, which are excellent candidates to help meet the regulatory, performance, and cost challenges of molding fuel tanks for lawn mowers, snow blowers, personal recreation vehicles, generators, and other small engines. Xenoy X6800BM blow-molding and Xenoy 6620-GT injection-molding resin grades provide a one-step, monolayer solution to help meet current and upcoming California Air Resources Board (CARB) and U.S. Environmental Protection Agency (EPA) standards governing vapor emissions from small engine off-road fuel tanks.

Xenoy resins avoid the high costs of traditional multilayer extrusion blow-molding processes, as well as the cost and time required for secondary fluorination of conventional monolayer molded tanks.

The new materials also provide an outstanding balance of mechanical performance and weatherability, and are available in both natural and pre-colored black.

“The increasingly strict requirements of CARB and EPA regarding fuel permeation in small engine tanks are driving the need for new material solutions,” said Craig Williams, industry manager, Transportation at GE Plastics. “Because existing multilayer and monolayer approaches involve significant complexity, GE Plastics developed the new Xenoy resins that offer molding simplicity, speed, high performance, and compliance with regulations – not just today, but into the future. Xenoy resins for small engine off-road fuel tanks provide a one-step molding solution to help customers meet new regulations while remaining competitive.”

Key applications for the new Xenoy resins include walk-behind consumer mowers, six million of which were shipped in the United States in 2006, and hand-held gasoline blowers and trimmers, with more than 8.6 million units shipped last year, according to the Outdoor Power Equipment Institute. Snowmobile fuel tanks are another large application, with about 90,000 snowmobiles shipped in the United States in 2006, according to the International Snowmobile Manufacturers Association.

Xenoy X6800BM and Xenoy 6620-GT resins not only comply with the current 2007/08 CARB standard, which limits fuel vapor emissions to 2.5g/m2/day for small off-road engines, but also comply with the tighter 2011/12 limit of 1.5g/m2/day. CARB requirements are becoming the de facto industry standard.

Compared to multilayer extrusion blow molding, a complex barrier solution that can require a capital outlay of $2 to $5 million for the equipment, blow- or injection-molding Xenoy resins is simple and may potentially utilize existing tooling.

In contrast to post-molding fluorination of monolayer parts, which requires a secondary operation and may perform unevenly, the new Xenoy resins incorporate an inherent barrier material that delivers consistent permeation resistance throughout the part.

Other benefits of the new materials include:

• Excellent high- and low-temperature ductility
• Excellent UV stability
• Efficient processing with robust regrind capability
• Ability to do hot-plate or vibration welding
• Available in black and natural color

Other applications include fuel tanks for jet skis, generators, chainsaws, rototillers, ice augers, go carts, power washers, golf carts, and other devices requiring small off-road engines.

For more information on GE’s Xenoy resin, please visit the GE Plastics’ website at www.geplastics.com.

POLL RESULTS

0

Our last poll asked you which 2008 sled will be the biggest hit. From 1,127 votes cast, the results were as follows:

56.79% – Ski-Doo REV-XP (640 votes)
31.50% – Yamaha Nytro (355 votes)
08.87% – Polaris Switchback 136 (100 votes)
02.84% – Yamaha Vector (32 votes)

LATEST QUESTION:

Which 2008 sled in this value range appeals to you most?

1. Polaris Shift
2. Ski-Doo 500SS
3. Yamaha Phazer
4. Arctic Cat F5

Scroll down to cast your vote!

Changing Oil Filter On New Yamaha Apex

Question:

Have any of you ever changed the oil filter on a new Apex? As much as I love the 4 stroke yamaha’s, the Apex oil filter change is ridiculous.

Richard

Response:

Thanks for your email!

The oil filter ritual on most 4-stroke snowmobiles can be a challenge. You need to think about how many times during the riding season you didn’t have to saddle bag oil bottles, fill up an oil tank daily (nightly?) or buy injector oil by the case when you are struggling with the once a year oil filter change.

I’m not trying to be smart but here’s where the rubber hits the road – new 4 stroke sleds are tightly packaged and because snowmobiles need a completely enclosed belly we are limited in access to the engine area. It’s the nature of our machines.

The fuel economy issue is intriguing. We ride our sleds hard and fast – honest. In fact we have some of North America’s best lake running at our Canadian facility located in Central Ontario. We run lakes at WOT all the time. Not good for mileage. Having said this – we have already seen 20 mpg (US gallon) from our Attak GT. Go figure. This sled has almost 2000 miles on it today.

In the past we have recorded over 21 mpg with a Vector/Nytro. We are not using factory tweaked units but real, full-on production sleds. Trails at high speed and lakes at WOT.

This season it has been difficult to get big numbers because we’ve been riding on what amounts to unpacked snow (no hard base) all season. We are having our first mild spell since the snow came.

With unpacked snow on trails skis tend to “sink” and generate much more parasitic drag than running on harder snow. When we’ve run on hard pack, we get better mileage – I would guesstimate as much as 20% better. When it’s loose and cold, we get less mpg on everything.

Hope this helps,

Motorhead Mark

REV 500 SS Inside Ski Lift Issues

Question:

First of all great web site. I have a 2005 500ss which is a great sled but has a lot of inside ski lift and is a bit tippy. Is there any way to get the the handling of the 2006 with the lower front end.

Also this sled has a lot of belt dust, way more than my cat had.

Thanks and keep up the good work.

Steve

Response:

Thanks for your question.

Your 2005 Rev 500 SS will settle down and stay flatter with a couple of subtle tweaks.

First, turn the coupler block on the rear drop link at least one position fatter (so a fatter side is pointing rearward.)

This will increase the coupling moment and reduce inside ski lift under power exiting turns. However, this will do little on entry with the throttle dropped.

To counter off-throttle inside ski lift you should take some pre-load off the front IFS shocks. Do this incrementally.

The change to the front end of the 06 Rev’s was most profound up front where SD actually reduced front IFS travel by 1.5 inches. By reducing preload you allow the sled to settle lower into the suspension stroke at static ride height.

You can also help your cause by reducing the front arm shock preload as well. If you have studs on the outside belts of your track – ditch them. They only make the situation worse.

If the sled can slide a little more in aggressive corners it will generate softer lateral forces and help you stay flatter in turns.

There is a downside to all of this. You will get somewhat heavier steering and you may sense a little more tendency to dip and duck side to side on straight-aways. This is a result of the softer preload you’ve dialed in.

Hope this helps.

Motorhead Mark

Polaris Dominates at Jackson Hole Hill Climb

Press Release –

Which brand dominates in the steep and deep? Check the facts: Racers on Polaris RMK® deep snow models won 45% of the class titles and the Mod King of the Hill title at the 32nd annual Jackson Hole (WY) World Championship Snowmobile Hill Climb.

The Polaris racers dominated the super-competitive 700 classes en route to winning nearly half of the titles and leaving Ski-Doo (30%) and Arctic Cat (25%) to split the rest.

“Jackson Hole is the biggest event in hill climbing and our Western guys used the RMK platform to win the lion’s share of the titles,” said Polaris Racing Manager Tom Rager, Sr. “Jeremy Osler and Rick Ward had great weekends and we ran strong in several 700 classes, proving the power of our new Liberty™ engines.”

JEREMY OSLER WINS MOD KING HONORS

Polaris hill climber Jeremy Osler (Bozeman, MT) won titles in the 600 Mod and 800 Mod classes and also won the Mod King of the Hill title.

Rick Ward, a legendary Polaris hill climber who still excels, won three class titles: 700 Stock, Pro Masters Improved Stock and Pro Masters Mod. He also finished second in Pro Masters Stock.

Others Polaris competitors to win class titles on Snow King Mountain were:
• Kirk Williamson (Young Ward, UT) won the 700 Mod class and was second in 800 Mod
• Erin Beukelman (Nampa, ID) won 700 Improved Stock
• Jay Stickney (Kalispell, MT) won 600 Stock and finished second in 600 Improved Stock
• Kyler Stone (Farr West, UT) won the Juniors title

POLARIS DOMINATES THE 700 CLASSES

Polaris hill climbers swept the top three positions in two 700 classes and ran 1-2 in a third 700 class. The podium sweeps came in the 700 Stock class, where Ward, Osler and Sandy Sletten (Pinedale, WY) ran 1-2-3, and 700 Improved Stock, where Beukelman won and was followed by Shane Hart (Lolo, MT) and Brook Beckstrom (Spanish Fork, UT).

Williamson won in 700 Mod and Cody McKinney (Pinedale, WY) finished second, and in the 800 Mod class, Osler won and Williamson ran second.

Such 700 class dominance was due in part to the incredible 2007 700 Dragon RMK, which was introduced at the start of the season to rave reviews by customers and media alike. Featuring the new RAW RMK chassis and a stout new 140hp 700 twin engine, the combination proved lethal to the competition at Jackson Hole.

NEW 800 RMK DRAGON DELIVERS WINNING PERFORMANCE

Building upon the success of 700 Dragon RMK; the 2008 Polaris 800 RMK and 800 Dragon RMK expand the dominance of the Polaris RAW RMK chassis with big twin power. Both the 800 Dragon RMK 155” and 163” feature the new 800 Liberty™ HO Cleanfire Injection™ engine pumping out a whopping 154 hp and pure, arm-stretching torque.

Both models are built on the RAW Polaris RMK chassis that is light, strong and balanced for sure, easy handling in the steep and deep. These models ride on the new Series 5.1 track (163” or 155”) with 2.4” lugs and an optimized lug pattern for 19% more forward lug contact.

2008 Polaris Shift: Simple is Better

0

Web Exclusive By: Kent Lester

When we first saw the 2008 Polaris IQ Shift last January, we thought it was one of the company’s test mules used for calibration. There were no markings on it at all, save for POLARIS logos on the sides of the seat. No graphics, no engine displacement numerals, no model name – nothing. The hood is uninterrupted deep black and there are no outside rear idler wheels in the skidframe.

On closer inspection it became obvious Polaris had left all the good stuff in. The fully coupled suspension featured Arvin gas cell shocks, there was a sway bar, snocross style seat and high quality plastic skis.

Its carbureted 600HO twin offered detonation control and a throttle position sensor and, better yet, with the shave job, the Shift had dropped about eighteen pounds. Much of the diet came from using a .91-inch Shockwave track but this sled is one of the lightest on the 2008 industry dance card.

The Shift is all about price and it comes at a critical time. The Shift offers less, costs less but gives you more on the bottom line – performance. Price is becoming a huge factor as complex technology has been causing price creep the last five years.

Nobody could have dreamed sleds would reach five digit prices but it=s happening – and the qualified market willing to pay those dollars is shrinking.

By offering a clean canvass, the sparsely equipped Shift opens the door to infinite personalization.

This sled can be thoroughly customized and plays to the twenty-something generation who have less earning power but eagerly want their tuner Honda, Acura or Cobalt to reflect personal individuality.

You can go wild and use aftermarket parts and graphics to get the same result. Besides, there are a bunch of optional graphic kits available from Polaris and you can upgrade the shocks or windshield, add a higher handlebar riser or install a deeper track – your choice.

You can personalize this sled any way you want and to the extent your budget will allow. Leave it alone and you’ll still be playing with a lightweight, great handling chassis that delivers an honest 120 horsepower.

Going the Distance to Help to Cure Diabetes

Press Release –

Here’s a challenge for you! Present me with a man with more thalamus based fortitude and ambition than Henry Bieda. This is a man that has gone through two divorces, a business and home leveling fire and two recessions which nearly crushed the family business.

His mind never gives up and fortunately he has a physique and level of health to compliment his lofty aspirations and internal drive.

Never sick for work a single day in over 33 years in business, Henry Bieda is a model of the entrepreneurial spirit, an example of how much one can accomplish in life with or without an education. Henry is a grade eight drop out. Unconventional, unorthodox, outspoken and downright controversial are some words that best describe this youthful minded and proud descendent of Polish immigrants.

If there was ever a guy that you could count on when times were tough to lend a hand or solve the impossible problem that others long ago gave up on, it would be Henry Bieda.

So it was really no surprise, when reports came in from Sweden last October that after 18 years, Henrik Lodin a man less than half Henry’s age was claiming to have achieved his personal 5 year goal of besting Henry’s 100 mile (162 km) snowmobile waterskipping distance record.

Needless to say, that it did not take long before Henry began formulating a plan to regain his claim to fame and do something really big to help others at the same time.

Henry’s 6 year old grandson Evan and 8 Year old granddaughter Peyton (Stephen’s children), both have Type I (Juvenile) diabetes, a debilitating disease that requires these kids to have 8 invasive blood glucose tests per day and requires Peyton who is not yet eligible for an insulin pump to endure as many as 4 insulin injections per day.

Fortunately, these kids have of some of Henry’s genes but many others are not so strong or lucky. Diabetes is the single most costly disease on our health care system in Canada and children and adults alike are being diagnosed with it at an alarming rate due to a combination of lifestyle and environmental factors.

Please take a few minutes out of your busy day to watch this video produced by our great friend and campaign coordinator John Gale.

CLICK HERE TO WATCH THE VIDEO NOW

You can help us reach our fundraising goal of $20,000 for Juvenile Diabetes Research by Saturday June 16th, 2007, the date Henry WILL REGAIN the Snowmobile Waterskipping World’s Record that he held since 1989 and later finally get recognized in the Guinness Book of World’s Records. Send this email to your friends!

Call (905) 333-4660